9/26/2023 0 Comments Diy panel lightThis allows the finished wall art to sit closer against the wall. I ordered battery powered LED lights for this project and needed to router a pocket into the back panel for the battery pack to sit. I sanded the panel down, then stained it and let it dry. You can use 1×2 boards for this as well, it will just sit further off the wall if you do. I glued up the edges, then stapled 1/4″ thick strips of wood to the back. To make up the back panel, I cut a 1×6 board into 24″ long pieces. Once the project was finished, I grabbed my Dremel to clean up the edges of the project as well as clean up the parts of the tabs left over from the carve. I would recommend using a downcut bit if you have one because it doesn’t give you the fraying you see with the upcut bit, leaving you with a much cleaner carve. Since I had broken my 1/8″ downcut bit, I used my 1/8″ upcut bit for this. You’ll switch back to a 1/8″ bit for this. Moving the design will cause it to carve off center of the rest of the project and essentially ruin all of your work. The design in that window is set up so that it will carve exactly where it needs to. Click on that window (DO NOT MOVE THE DESIGN) and set it up to carve. In my project within Easel, this is a second window. When the detail pass was completed, I moved on to carving the design out from the panel. I started up the detail pass and it cleaned up all of the stars and stripes in the design. Once the roughing pass was completed, I carefully swapped out the bits so as not to move the spindle at all, then installed my 60 degree V bit. This takes out a good portion of the material quickly and saves some time. Everything went just as planned.įor the first portion of the carve, I used a 1/8″ upcut bit for the roughing pass. Third carve – left the dust shoe off and worked REALLY hard to ensure that when switching out bits, I didn’t move the spindle AT ALL.When I realized what was happening, I stopped the carve, but the spindle didn’t raise fully and it broke my bit. This caused the spindle to keep carving deeper and deeper through the design and into my waste board. When the design was finished and it was carving out the whole design from the panel, I briefly lost my internet connection. I stopped the carve and was able to correct the mistake, and continue carving. Second carve – I had been using my dust shoe and when I took it off to switch the bits between the roughing pass and detail carve, I moved the spindle slightly.I flipped the panel over, spray painted the other side and waited for it to dry. I started carving and quickly realized that it would end up carving off the material and stopped the carve. First carve – my design was not positioned properly over the material.I’ll be honest, it two three different tries to get this to carve correctly for me. I sprayed several coats going side to side and also up and down to ensure even and full coverage over the panel. Once the panel was prepped, I spray painted it black. You can either use an orbital sander or a combination of orbital sander and drum sander to get your panel smoothed out. ![]() Once the glue was dry, I sanded the panel down. I used select pine for this panel as there are no knots in it and it provides a very clean carving area. Prepping The Wood To Carveįor this project, I glued up a 1×12 and a 1×4 to create my project panel. It saves A LOT of time over carving the whole thing with the 60 degree bit. First using a 1/8″ uncut bit to rough out the design, then switching to a 60 degree V bit for the finer details. I used this function when carving out the American flag design on this project. If you’d like to take it a step further, you can also try out their Easel Pro subscription, which will expand your carving even further with the usage of V-bits and also multiple bits per carve. All you need to do is sign up for an account and you’re ready to start creating. The free Easel program from Inventables is simple to use. You can upload your own artwork into the Easel program from Inventables, or you can use this custom artwork I created. When it comes to creating the wall art, it’s as simple as choosing a design. Should you make a purchase from one of these links, I will earn a small commission at no extra cost to you. I’m partnering with my friends over at Inventables to show you how I made this backlit LED wall art for my oldest son’s bedroom on my X-Carve CNC. Have you ever worked on a project with LED lights? I’ve been really intrigued by CNC carved LED backlit wall art that I’ve seen lately and I wanted to create a project myself. Use the X-Carve CNC to carve your custom design and inexpensive LED lights to make it shine. Learn how to create your own custom LED backlit wall art using this step by step tutorial.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |